For 2006-2012 Ford Fusion models with a standard ignition, turn the ignition off, step on the brake pedal, and cycle the ignition three times within 10 seconds. This initiates the relearn mode, indicated by a horn chirp and a message. Then, you move to each tire, activating the TPMS sensor using the TPMS reset tool.
For 2013 and newer Ford Fusion models, ensure the vehicle is off, then press the brake pedal and cycle the START button a specific number of times based on your ignition type. The rest of the steps are the same as the standard ignition.
We will discuss the reset procedure for the Ford Fusion Tire Pressure Sensor Fault in detail in this article.
Ford Fusion Tire Pressure Sensor Fault: What Does It Mean?
Tire Pressure Sensor Fault” means one or more of your tire pressure sensors are not working. In this case, you must determine the faulty ones and resolve the issue. If you’re facing similar problems with a Ford F150, you can also read our article on Ford F150 Tire Pressure Sensor Fault for specific guidance.
Tires are equipped with pressure monitoring sensors, or TPMS, which measure the air pressure inside the tires to prevent accidents caused by underinflated tires.
To determine the faulty sensor, you need to perform a Ford Fusion TPMS reset.
Ford Fusion Tire Pressure Sensor Fault: How To Reset the TPMS?
Resetting the “Tire Pressure Sensor Fault” message in your Ford Fusion is quite easy to do. To reset the TPMS in your Ford Fusion, you will only need a TPMS reset tool. Also, in a push-button ignition, the reset procedure differs slightly from a standard ignition.
Here is how you can reset the TPMS in your 2006-2012 Ford Fusion models that have a standard ignition-
- Turn the ignition to the off.
- Step on the brake pedal and release it.
- Turn the ignition three times from off to on without starting the car.
- Repeat steps 1-3.
- The relearn mode will be indicated by a single horn chirp and a message, “Train Left Front Tire.”
- Get close to the left front tire and press the TPMS tool button until you hear a single horn.
- Repeat for the right front, right rear, and left rear sensors
- When relearn is complete, the message center will display TRAINING MODE COMPLETE
NOTE: The steps 1-4 for this process must be performed within 10 seconds.
Now, if you have a Ford Fusion model that is 2013 or newer, here is what you need to do-
- Make sure the vehicle is off.
- Step on the brake pedal and release it.
- Push the START button 5 times. You need to do it 8 times if you need to push the button twice to start the engine.
- Press and release the brake pedal
- Push the START button 6 times. You need to do it 9 times if you need to push the button twice to start the engine.
- A single horn chirp will indicate the relearn mode is active.
Now that the relearn mode is active, the rest of the process is the same as a standard ignition.
Can You Perform Ford Fusion TPMS Reset Without Tool?
Yes, you can perform a Ford Fusion TPMS reset without the tool. To do so, once you have activated the relearn mode, release some air from the tire until you hear a single horn. If you do not hear a horn even after releasing a significant amount of air, it indicates that the sensor is damaged.
Can You Drive With a Tire Pressure Sensor Fault?
You can drive with a tire pressure sensor fault, but it isn’t recommended. TPMS keeps you safe by alerting you to low tire pressure. If the TPMS does not work properly, you may not be aware of a low tire pressure situation. As a result, there may be several safety hazards.
How To Fix a Faulty Tire Pressure Sensor?
If you have one or more sensor is bad, it could either be a faulty sensor or a dead sensor battery.
If the battery is replenished, you need to put in a new battery for the sensor. But unless you are an expert in doing these sorts of things, it’s better to just hire someone to do that.
The sensor is located in the rim of the wheel, so you will have to remove the tire to access it. So, unless you have the tools and the skills, this is not a DIY job.
Also, if one of the batteries is dead, then it may also mean the others will follow soon. So, it’s better to change the batteries of all of the sensors together.
In TPMS sensors, coin batteries are used, which are very cheap, around $5-$10. The labor cost of replacing the battery is about $50-$150.
The battery is often molded into the sensor, so replacing it could prove challenging, even if it would be cheaper. Some suggest replacing the whole sensor instead.
The TPMS sensor can also be difficult to access, so it’s best to leave it to a professional. In that case, you may have to spend around $260-450 to replace all the sensors.
If you don’t go with OEM sensors, you can get a set of four aftermarket sensors for around $25-$30. OEM sensors, on the other hand, can cost up to $50 per set.
When Should You Reset the TPMS?
The TPMS reset is not only for when you see a “Tire Pressure Sensor Fault.” There are other times when you need to perform this procedure-
- After you have refilled your tires with air. The TPMS system needs to be reset after you have refilled your tires with air, even if the pressure is within the recommended range. This is because the sensors need to be recalibrated to the new pressure levels.
- After you have replaced a tire. If you have replaced a tire, you will need to reset the TPMS system so that it can learn the new tire’s pressure.
- After you have replaced the TPMS. If the TPMS system has been replaced, you will need to reset it so that it can function properly.
Tips For Avoiding Tire Pressure Sensor Fault in Your Ford Fusion
To make sure you don’t run into tire troubles down the road, just follow these easy steps:
- Give your tires a quick pressure check once a month, especially if you’re driving in super hot or cold weather.
- Get yourself a decent pressure gauge. Cheap ones can give you wonky readings, and that’s not good.
- Have your tire pressure monitoring system (TPMS) looked at once a year or even sooner if it’s been acting up.
- Try your best to dodge potholes and road bumps. But if you do hit one, get your TPMS checked out, just in case.
- Keep your tires clean. Dirt and junk can mess up your TPMS.
- If you’re stashing your tires away for a while, find a cool, dry spot for them.
Follow these simple steps, and you’ll have smoother travels and healthier tires!
Conclusion
Ford Fusion Tire Pressure Sensor Fault might not seem like a big deal, but if you ignore it, you could cause a serious accident. If you see this message, make sure you check the pressure in your tires immediately.
Last Updated on September 26, 2024 by Rifen